14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.
|Published (Last):||12 February 2005|
|PDF File Size:||4.13 Mb|
|ePub File Size:||12.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
Glider, 2 ailerons or more These functions call the ailerons, elevators, and flaps camber flaps, brake flaps trim offset rates 14m according to the flight state. To correct this use the Hovering Point function.
Make sure your transmitter is off, and use the attached 2. You can use the toolbox contained in the set for various adjustment of the transmitter. Push the user’s name. The clock for the transmitter depends on the Lithium battery.
Throttle-stick Calibration Futaba 14MZ and FX40
Replaceable switches You can replace 8 of the toggle switches on the right and left shoulder, with optional switches two position, three position, and momentary etc. Always charge Li-Ion batteries in a fireproof location. Servo connection by model type The T14MZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.
Manual for update Futaba 14MZ will you find here: Display adjustment and auto power off setting. Connect the power cable to the charger. Functions and mixing functions necessary for each model type are set in advance at the factory.
When you are using a new PCMG3 receiver and changing the frequency, set ID or frequency by the following instructions. The T14MZ system program version information, CF card information memory size, vacant capacity, number of model data, and number of music filesand product ID are displayed on the Information screen.
The offset amount of the aileron, elevator, and flap servos can be adjusted as needed.
Futaba 14MZ Manuals
The servos operate smoothly at a constant speed corresponding to the set speed. It is also recommended to charge the battery just before your usage.
Timer Timer setting and lap time display. Page Curve setting operation This section describes the ,anual procedure of curves which are used with the AFR function and each mixing function. Switch can be set. Camber Mix Camber Mix [Corresponding model type]: Return to System Menu Non-corresponding types of transmitters: Insert the switch block so that it fits correctly into the body of the transmitter as shown in the picture and manyal the hexagonal 1mz to tighten the screws.
To print the manual completely, please, download it. Servo connection by model type The T14MZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.
Page 70 Dial Monitor LDisplays the position of the dials, slider levers, and digital trim. Gyro sensitivity and mode switching The gyro sensitivity and mode switching function is dedicated gyro mixing of the Model Menu, and can be set for each condition. Switch selection method The various functions used in the T14MZ can be selected by switch.
Receiver and servos connection – Futaba 14MZ User Manual
Hook one of your fingers in the slit formed by the transmitter’s main body and the battery cover on the back and bottom of the transmitter, and then pull up the cover to release the lock. Then ID inputting screen for receiver will pop up.
Return to System Menu Date setting 1. This device complies with part 15 of the FCC rules. And be sure that the servo 14,z do not touch directly to the metal Connecting connectors parts such as servo mount. Do not use the transmitter as it is, send it back for a check to the Futaba Service Center.
Always contact your region’s support center for assistance. Three operating modes are available.
The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. This equipment must not be utilized to operate equipment other than radio controlled models. Otherwise set it to “8CH”. Sounds recorded with the microphone built into the transmitter and audio files.
If you modify the location of the switches on the right and left top of the transmitter, you should be sure to re-assign functions to the switches for proper operation.
Call the setup screen by pressing the function you want to set up. Curves which 41mz symmetrical to the left and right of center can also be set. This manuak reverses the actual operation This function reverses the operation signal of the signal, but does not change the display of sticks, switches, trimmer levers, and knobs. And do the procedure 6 and 7. A typical menu screen is shown selection, frequency setting, end point setting, and below.